• liste
  • Bir Arkadaşına Söyle

Minke

$ 69,000
Owner Stock No
239540
Başlık
Minke
Şehir
Indiantown, FL
Oluşturulmuş
1995
CARTWRIGHT Steel Hybrid Pilothouse Cutter CARTWRIGHT Steel Hybrid Pilothouse Cutter
Single, Other, Other, Electric
Açıklama

\"Minke\" is the ultimate self-contained self-reliant world cruiser. With a brand-new electric drive engine (well over $30,000 in value just for the engine and batteries) and all systems built, replaced or modified by her engineer owner, she is the boat for you if you want to cruise exotic places in safety and comfort and self-sufficiency!



Don't miss the opportunity to own this incredible steel sailing ship! A boat like this comes along once in a lifetime, and it is the last boat you will ever need. NEW generator. New refrigeration. New batteries. Extensive  Both 110 and 220 (European) compatible electrical circuits for world cruising. Dual helm stations in pilothouse and in cockpit. Not a spot of rust, beautifully maintained. Reinforced steel plating. Extensive work done over last year!





  • 1995 36 foot, Steel hull, Flush Deck Pilot House, Cutter Rig 


    Sailboat, Jerry Cartwright design, long fin keel with skeg hung 


    rudder


  • 20K.W. Electric Propulsion by Electric Yacht


  • Only been in salt water for 7 months of her life


  • LOA 36ft, LWL 29ft, Draft 5ft, Beam 11.5 ft, Bridge clearance 52 


    ft


  • Repowered with a QT20 Electric Drive by Electric Yacht. 20 Kw 


    output. Throttle controls at each helm


  • 208 amp hour 48 Volt drive battery pack of Torqeedo Lithium Ion 


    batteries model 26-104 installed 9/2016


  • Lithium drive battery chargers (2) 1700 Watt Torqeedo fast 


    chargers


  • 3 blade Michigan Wheel DJX 18” prop, and a spare 3 blade prop


  • 5.5 KW Next Generation Power diesel generator (520hrs) installed 


    10/2016


  • Shore power isolation/step down transformer. 5Kva will accept 


    Euro240v power and put out 120v power by moving leads in the 


    transformer


  • (2) 50foot long 30 amp shore power cords


  • The rig is a deck stepped aluminum mast and boom by Klacko


  • Spars, single spreader mast, cutter rig with folding steps to top of 


    the mast. Standing rigging 5/16” 1/19 stainless steel. Removable 


    cutter stay and running back stays. Spare halyards for each sail on 


    mast


  • All running rigging is lead aft to the cockpit through Garhauer 


    and Schaefer blocks to Spinlock clutches


  • (5) stainless steel winches all in cockpit: (2) 2 speed Anderson


  • 40ST self-tailing, (2) Barlow 20, (1) 1speed Anderson 12ST self-tailing


  • Adjustable 11/4” Genoa sheets tracks and cars


  • Pro Furl model C32 roller reefing on forestay


  • Adjustable Mainsheet traveler aft of cockpit, with ball bearing 


    block and tackle


  • Wagner Engineering Hydraulic steering 2 helm stations


  • Emergency tiller


  • Sails: Genoa 120% roller reefing, (2) Main sails slab reefing: Full 


    batten 2 reef points, 315 sq. ft. Dacron 8oz with shorter battens 3 


    reef points, 3 hank on stay sails one is a heavy storm sail. Main sail 


    cover and deck sail bag for staysail


  • Forespar Telescoping twist-lock whisker pole


  • Bimini cockpit sun shade


  • GPS chart plotter Standard Horizon 155C; with chart chips for 


    Great Lakes Eastern Canada, East Coast of the USA, Bermuda and 


    Bahamas


  • Compass Ricthie Globe Master 5 inch diameter for steel boat with 


    brass binnacle mount


  • Raytheon ST4000 auto helm wheel autopilot installed inside 


    pilothouse


  • Raymarine ST40 wind instrument and ST40 Bi-data with depth, 


    knot meter, and water temperature


  • Raytheon Ray53 DSC VHF radio


  • SSB Icom IC-M600 radio and AT-120 auto antenna tuner


  • Pioneer stero Bluetooth CD player installed 1/2017


  • EPIRB by ACR new 10/2016


  • Water tank Plastimo 40 gallon flexible tank new 10/2016


  • Force 10 water heater 6 gallons


  • Fuel tank, steel 28 gallons + (4) 5.3 gal jugs for more storage on 


    deck


  • Refrigerator 12 volt NovaKool compressor condenser and 


    evaporator/freezer box


  • New insulated refrigerator box installed 


    9/2016


  • Hot and cold pressure water 12volt automatic FlowJet pump


  • Brass galley sink hand pump by White Star Products for salt water, 


    with a spare rebuild kit


  • Force 10 Kerosene cabin heater with 2 gallon tank


  • Smoke and CO detectors


  • Force 10 gimbaled 3 burner propane stove with oven, Trident Gas 


    Control alarm and solenoid shutoff at tank


  • Fiberglass Propane 


    tank installed in locker on stern rail


  • Force 10 BBQ rail mount with small propane tank


  • All Cabin lighting LED bulbs


  • Navigation lights are all LED bulbs


  • Maxwell HRC-10 Electric Windlass for rope and chain


  • 2 Anchors;45lb Bruce with 120ft of chain, 35lb CQR attached to 


    20ft of chain and 120ft nylon rode


  • House battery bank 2 Rolls 350Ahr 6v wet cells connected in 


    series


  • 50 Amp max output 48volt to 12volt DC converter to power house 


    loads from drive batteries


  • Air Breeze wind generator, blades, brushes, and yaw tube 


    assembly replaced 10/2016


  • West Marine 8ft roll up inflatable dinghy, with anchor, 2 


    outboards, and oars


  • Torqeedo Travel 1003, 3 hp electric outboard new 1/2017 


    Johnson 2 hp 2 stroke outboard


  • Head Lavac with 25 gallon holding tank, Y valve and offshore 


    pump out


  • Shower with floor sump in the head


  • Various nylon dock lines and spring lines, and boarding steps


  • Fenders and stainless steel storage baskets on stern pulpit


  • 3 life jackets, Plastimo lifesling, Life ring


  • Sextant, safety equipment, signal horn, bosons chair, cockpit 


    cushions


  • 3 electric fans in cabin


  • 4 Winch handles


  • Spare parts and filters for generator





    Boat Name


    Minke






    Specs


    Designer: Jerry Cartwright


    Keel: Fin








    Dimensions


    LOA: 36 ft 0 in


    Beam: 11 ft 6 in


    LWL: 29 ft 0 in


    Maximum Draft: 4 ft 6 in


    Displacement: 20000 lbs


    Ballast: 5000 lbs








    Engines


    Engine 1:


    Engine Brand: Electric Yacht


    Year Built: 2016


    Engine Model: QT20 Electric Drive


    Engine/Fuel Type: Other


    Drive Type: Direct Drive








    Tanks


    Fresh Water Tanks: (40 Gallons)


    Fuel Tanks: (28 Gallons)








    Accommodations


    Number of single berths: 2


    Number of double berths: 2


    Number of cabins: 2


    Number of heads: 1








    Electronics


    GPS


    Radar


    Autopilot


    Depthsounder


    Wind speed and direction


    Navigation center


    Log-speedometer


    Compass


    Repeater(s)


    VHF


    Plotter








    Sails


    Furling genoa


    Storm jib


    Gennaker/Cruising spinnaker


    Battened mainsail








    Rigging


    Spinnaker pole


    Steering wheel








    Inside Equipment


    Battery charger


    Manual bilge pump


    Fresh water maker


    Electric bilge pump


    Marine head


    Deep freezer


    Sea water pump


    Hot water


    Oven


    Refrigerator








    Electrical Equipment


    Generator


    Inverter


    Shore power inlet


    Electrical Circuit: 12V








    Outside Equipment/Extras


    Swimming ladder


    Wind generator


    Tender


    Electric windlass








    Covers


    Mainsail cover





























    The Story Behind Minke's Repower




    From the owners:



    Back in July 2016, while motoring down the Richelieu River, our Perkins 4-108 diesel engine completely failed and was not able to be rebuilt. My husband, Dan, and I were devastated but after many hours of researching possible solutions we decided to go the electric/hybrid route. The electric/hybrid system supports our desire to reduce our carbon footprint and even if we wanted to install a new diesel replacement we couldn’t since the marina we were stuck at didn’t have the capability to install the engine into our boat.



    With the decision made we then furiously began researching companies that could re-power s/v Minke with an electric/hybrid system. Luckily, we found a person that had the drive and the will to help us reach our goal. Nancy Frainetti, the owner of The Electric Marina and a dealer for Electric Yacht, began sending emails with the possibilities of what we could do to get Minke up and running again. After a flurry of emails back and forth with Nancy relaying calculations formulated by Scott McMillan, and Mike Gunning at Electric Yacht, we decided to go forward with the QuietTorque 20.0 kW, 48 Volt package powered by four Torqeedo Power 26-104 batteries and two 1700W Torqeedo chargers. The calculations were based on the total displacement of our boat (24000 lbs), the waterline beam (10'6\"), length of waterline (29') and an estimation of RPM at different knot speeds when we were running with our Perkins engine.



    Setting aside the stress of what we were going to replace the old diesel with, we began tearing the old engine apart piece by piece. Most of the electric/hybrid installation videos that you can watch online show the old engine being whisked away easily from the hull with the use of a crane. Unfortunately, that was not a possibility at our current location so the engine had to be downsized. Most of the smaller pieces were easily removed except for the engine block and transmission which each weighed about 150 lbs after being completely disassembled. With the use of our Canadian Tire chain fall hoist, we were able to pull it out of the engine compartment, then with a lot of heavy lifting up the stairs, we carefully slid them out the hatch to the edge of the boat and down a plank into a cart. It was a great feeling once the engine and transmission were removed and thanks to Trans Atlantic Diesels we were able to sell our parts for a few dollars.



    The next steps to follow included cleaning the engine compartment with degreaser and repainting it. Metal mounts for the new electric motor were fabricated as well as platforms to mount the batteries. The large wire connections were cut to length terminals were installed, and the Electric Yacht Display and two throttles were mounted. Once the batteries were installed and secured they were connected into a series parallel bank in order to produce 48 Volts with 208 amp hours. Connections were made from the power relays to the batteries, chargers and fuses were installed and power from the batteries was connected to the motor. Since we needed to produce electricity while we are motoring down the river we bought a 5.5 kW gas generator to use on the deck powering us until got to the Canadian/US border at Rouses Point NY.



    After a little over a month of constant work, Dan and I pushed the silver Torqeedo battery button, waited for the red light to blink and then we turned the key. The throttle lever was slid forward and the propeller shaft began to rotate. After such a long wait the cobwebs between Minke and the dock were ripped away, we had power once again and the sweet hum of the motor was music to our ears.



    After finally making it across the border Minke was hauled out in NY at Gaines Marina. During the two weeks on the hard we installed an Ultra Compact Marine 5.5 kW Next-Gen diesel generator, change out our propeller to a new Michigan Wheel DJX 18inch diameter 15 pitch and repainted Minke's underside so she was ready for the push down to FL. We were under way heading South through Lake Champlain to the Hudson river. We noticed Minke moves so much better than with her old Cambel Sailor prop 18 inch by 11 inch pitch. We can reach hull speed and maneuvering at slow speed has improved so much! One of my favorite improvements is that the Electric drive makes close quarters handling so much simpler. We have even been able to back into docks which was not possible before.With the old Perkins diesel we had a separate throttle and transmission lever for forward and reverse. I always felt like I needed 3 arms to operated the levers and wheel when coming into a dock. With the new system we can easily transition between forward and reverse with the use of one simple lever plus we do not have to worry about harming a transmission if we need to quickly put the throttle in reverse.



    Motoring south through Lake Champlain we decided to collect data on the output of the electric motor and we noticed that with the new prop the motor was not reaching the recommended RPM’s and amp draw that would operate most efficiently. We contacted Scott and Nancy and without hesitation, they shipped a set of pulleys and belts to better match the motors to the Prop. When we arrived at Catskill, NY to re-step our mast, the pulleys and belts were waiting for us. Switching the pulleys and belts was simple and only took about and hour. With our mast up and the QT20 motor now at a better ratio it was time to get moving south one again.



    We had read that our propeller would be able to regenerate power while we were sailing but since we are a slow boat I was not expecting too much to come from this. I think that the choice of our lithium batteries and their voltage has made it less likely that we will get much regeneration from the propeller unless the bank voltage is low. While sailing through the Chesapeake Bay we were able to see regeneration from the Propeller. Our Torqueedo battery bank when fully charged has a voltage of 58.2V. I noticed regeneration from the prop when the batteries were about 52V. When sailing at around 5 Knts the state of charge meter displays the motor turning between 500 and 550 rpm. Input amps to the batteries was around 1.5A but we did see up to 7 amps for a short period when we had a few gusts that pushed us up above 6 Knts but most of the time it is in the 1.5Amp range (I have included a chart with some data on the speed and amp draw).



    After 3 months of daily use we have been extremely satisfied with our purchase. We were not planning to re-power but the benefits from our electric propulsion system have been numerous. I would also like to state that the customer service that we have received has exceeded our expectations and we are so happy to have found such a great crew to support us through this re-powering process.



    Below are some photos that were taken and our journey on Minke can be followed at:






































    Minke's Equipment List




    20K.W. Electric Propulsion by Electric Yacht


    Only been in salt water for 7 months of her life


    LOA 36ft, LWL 29ft, Draft 5ft, Beam 11.5 ft, Bridge clearance 52


    ft


    Repowered with a QT20 Electric Drive by Electric Yacht. 20 Kw


    output. Throttle controls at each helm


    208 amp hour 48 Volt drive battery pack of Torqeedo Lithium Ion


    batteries model 26-104 installed 9/2016


    Lithium drive battery chargers (2) 1700 Watt Torqeedo fast


    chargers


    3 blade Michigan Wheel DJX 18” prop, and a spare 3 blade prop


    5.5 KW Next Generation Power diesel generator (520hrs) installed


    10/2016


    Shore power isolation/step down transformer. 5Kva will accept


    Euro240v power and put out 120v power by moving leads in the


    transformer


    (2) 50foot long 30 amp shore power cords


    The rig is a deck stepped aluminum mast and boom by Klacko


    Spars, single spreader mast, cutter rig with folding steps to top of


    the mast. Standing rigging 5/16” 1/19 stainless steel. Removable


    cutter stay and running back stays. Spare halyards for each sail on


    mast


    All running rigging is lead aft to the cockpit through Garhauer


    and Schaefer blocks to Spinlock clutches


    (5) stainless steel winches all in cockpit: (2) 2 speed Anderson


    40ST self-tailing, (2) Barlow 20, (1) 1speed Anderson 12ST self-tailing


    Adjustable 11/4” Genoa sheets tracks and cars


    Pro Furl model C32 roller reefing on forestay


    Adjustable Mainsheet traveler aft of cockpit, with ball bearing


    block and tackle


    Wagner Engineering Hydraulic steering 2 helm stations


    Emergency tiller


    Sails: Genoa 120% roller reefing, (2) Main sails slab reefing: Full


    batten 2 reef points, 315 sq. ft. Dacron 8oz with shorter battens 3


    reef points, 3 hank on stay sails one is a heavy storm sail. Main sail


    cover and deck sail bag for staysail


    Forespar Telescoping twist-lock whisker pole


    Bimini cockpit sun shade


    GPS chart plotter Standard Horizon 155C; with chart chips for


    Great Lakes Eastern Canada, East Coast of the USA, Bermuda and


    Bahamas


    Compass Ricthie Globe Master 5 inch diameter for steel boat with


    brass binnacle mount


    Raytheon ST4000 auto helm wheel autopilot installed inside


    pilothouse


    Raymarine ST40 wind instrument and ST40 Bi-data with depth,


    knot meter, and water temperature


    Raytheon Ray53 DSC VHF radio


    SSB Icom IC-M600 radio and AT-120 auto antenna tuner


    Pioneer stero Bluetooth CD player installed 1/2017


    EPIRB by ACR new 10/2016


    Water tank Plastimo 40 gallon flexible tank new 10/2016


    Force 10 water heater 6 gallons


    Fuel tank, steel 28 gallons + (4) 5.3 gal jugs for more storage on


    deck


    Refrigerator 12 volt NovaKool compressor condenser and


    evaporator/freezer box


    New insulated refrigerator box installed


    9/2016


    Hot and cold pressure water 12volt automatic FlowJet pump


    Brass galley sink hand pump by White Star Products for salt water,


    with a spare rebuild kit


    Force 10 Kerosene cabin heater with 2 gallon tank


    Smoke and CO detectors


    Force 10 gimbaled 3 burner propane stove with oven, Trident Gas


    Control alarm and solenoid shutoff at tank


    Fiberglass Propane


    tank installed in locker on stern rail


    Force 10 BBQ rail mount with small propane tank


    All Cabin lighting LED bulbs


    Navigation lights are all LED bulbs


    Maxwell HRC-10 Electric Windlass for rope and chain


    2 Anchors;45lb Bruce with 120ft of chain, 35lb CQR attached to


    20ft of chain and 120ft nylon rode


    House battery bank 2 Rolls 350Ahr 6v wet cells connected in


    series


    50 Amp max output 48volt to 12volt DC converter to power house


    loads from drive batteries


    Air Breeze wind generator, blades, brushes, and yaw tube


    assembly replaced 10/2016


    West Marine 8ft roll up inflatable dinghy, with anchor, 2


    outboards, and oars


    Torqeedo Travel 1003, 3 hp electric outboard new 1/2017


    Johnson 2 hp 2 stroke outboard


    Head Lavac with 25 gallon holding tank, Y valve and offshore


    pump out


    Shower with floor sump in the head


    Various nylon dock lines and spring lines, and boarding steps


    Fenders and stainless steel storage baskets on stern pulpit


    3 life jackets, Plastimo lifesling, Life ring


    Sextant, safety equipment, signal horn, bosons chair, cockpit


    cushions


    3 electric fans in cabin


    4 Winch handles


    Spare parts and filters for generator






































    Broker's Notes




    Wow! This is the best equipped steel cruising vessel that I have ever seen. If you are an adventurer who wants to sail around the world with peace-of-mind and self-sufficiency, this is the boat for you. The owners have spared no expense in outfitting her. Their cruising plans changed, and it is up to you to pick up where they left off.



    \"Minke\" was professionally built in Canada at Shipham Boat Works in 1995 and was a freshwater boat for her entire life up until 2016. She is a multi-chine mild steel boat with reinforced steel stringers, an impressive grid system, and all the reinforcement one could possibly want in her construction. There are no bare steel surfaces--all surfaces have been coated with top-quality epoxy finishes. Her hull shines, and her bottom paint and zincs are all brand new.



    Pre-purchase survey from 2016 available on request, but this was completed before the -current owners completely refitted her.



    Currently hauled in Indiantown, FL. Call me! 305-807-4096!











 

    • : 0
    • : 0
  • 211 Gösterir
Arkadaşınızın Adı *
Arkadaşınızın E-posta Adresi *
Adınız
E-posta adresiniz
Mesaj
Güvenlik kodu *
Güvenlik kodunu yenilemek için resmin üzerine tıklayın. Lütfen resimde gösterilen karakterleri girin
Oturum aç
Kullanıcı adı
Şifre
Şifrenizi mi unuttunuz? Hatırlat